Do you have to put shoe molding?

1
Tessie Kulas asked a question: Do you have to put shoe molding?
Asked By: Tessie Kulas
Date created: Tue, Jun 1, 2021 5:52 PM
Date updated: Tue, May 24, 2022 7:27 PM

Content

Top best answers to the question «Do you have to put shoe molding»

It depends on what your clients are looking for, and how they feel about the expansion gap between the floors and the wall. If the homeowners are concerned about the expansion gap, you might want to consider installing shoe molding to cover it up.

FAQ

Those who are looking for an answer to the question «Do you have to put shoe molding?» often ask the following questions:

👠 Do you have to use shoe molding?

  • The main use for shoe molding is to run along the intersection of the baseboard and floor. Using shoe molding gives the floor installer more latitude in their end cuts and also allows the trim carpenter to hide un-level floors.

👠 Do you have to paint over shoe molding?

  • Paint or stain shoe molding before you install it. Then fill nail holes and add a little touch-up paint afterward, if necessary. It can be difficult to paint or finish small molding along the floor without getting paint or stain on the floor.

👠 How big does shoe molding have to be?

  • Standard shoe molding, available at home improvement centers and lumberyards, comes in widths of 7/16-inch to ½-inch and ranges from ¾-inch to 1-inch in height. It’s also made in a variety of material options to match the different types of baseboard.

Your Answer

We've handpicked 25 related questions for you, similar to «Do you have to put shoe molding?» so you can surely find the answer!

How to attach shoe molding?

How to install shoe molding?

  • Pour the liquid nails into the caulk gun cartridge. Cut the tip about 1/4″. Puncture the seal of the canister.
  • On a clean work area,lay down the shoe molding face down and apply a bead of liquid nails in a zig-zag pattern so it covers the length of the ...
  • Put the molding up to the wall with the adhesive side facing the wall and press firmly into place. Carefully make sure everything is lined up.
How to bend shoe molding?
  • How to bend the moldings? Water or steam will allow most wood to bend, and is especially effective with oak. The Pipe Soaker. One simple rig is simply to take a large PVC drain pipe, block off on end and then either stand it up or lean it on an angle that will allow you to fill it with water and then slide in the molding.
How to cut shoe molding?
  • Cut 2 joint pieces at 45-degree angles in the same direction (meaning both angled to the left,or both to the right)…
  • Most corners will be 90-degree angles…
  • For corners that are very different from 90 degrees,measure the angle with a protractor,and divide this number by 2 to determine the angle of your cuts.
How to install shoe molding?
  • Pour the liquid nails into the caulk gun cartridge. Cut the tip about 1/4″. Puncture the seal of the canister.
  • On a clean work area,lay down the shoe molding face down and apply a bead of liquid nails in a zig-zag pattern so it covers the length of the ...
  • Put the molding up to the wall with the adhesive side facing the wall and press firmly into place. Carefully make sure everything is lined up.
How to miter shoe molding?

What's the best way to cut out shoe molding?

  • Cut outside corners. Cut diagonal outside corners. Sometimes your baseboards or wall may not meet at a 45 degree angle, but instead have a flat, diagonal corner. If this is the case, cut your molding pieces at 22.5 degrees and make sure that the back side of the middle piece matches the length of the diagonal face.
How to stain shoe molding?
  • Use a high-quality 2 inch brush to apply the semi-gloss for the best results. Make sure you match the shade and type of stain if you want the finishes to match exactly. It’s also important that you use the same type of wood filler as the species of wood used in the shoe molding. This will ensure an even texture and grain when staining.
Should i use shoe molding?
  • Shoe molding is needed in situations when the subfloor/slab is uneven. The undulations in the floor's surface will cause gaps to appear between the baseboard and the flooring material. Shoe molding conforms to the floor's surface and hides those gaps.
What is base shoe molding?
  • A base shoe or shoe molding is a strip of wood next to the floor on the interior baseboard. It is also similar to a quarter round only 5/8” x ¾” in size.
What is shoe trim molding?
  • Shoe molding is a type of decorative trim piece primarily utilized for concealing small irregularities between the wall and floor of a structure. Shoe molding is installed at the base of a wall and typically attached to a much taller baseboard. This narrow molding has two flat sides facing inward and one concave side facing outward.
When to use shoe molding?
  • Shoe molding is needed in situations when the subfloor/slab is uneven. The undulations in the floor's surface will cause gaps to appear between the baseboard and the flooring material. Shoe molding conforms to the floor's surface and hides those gaps.
Where to nail shoe molding?
  • Press shoe molding firmly against the floor and against the baseboard as you nail it in place. The flexibility of the molding makes it easy to do this. Insert one finish nail approximately every 12 inches along the baseboard.
Do you have to use nails to install shoe molding?
  • A lightweight molding is a good option if you are using construction glue and not using nails. With your measuring tape, measure the area that you will be installing the shoe molding. Put the molding flat against the miter saw, making sure it is face up, and cut it to the measured length.
Can shoe molding floor and decor?
  • Shoe molding adds a decorative touch while covering any gaps that might lie between the bottom of baseboard and the floor. Not all types of baseboard are suitable for installing shoe molding, however, so keep reading to find out if this slim trim is right for you—plus how to install it flawlessly. Photo: homedepot.com
Can you paint plastic shoe molding?

In most cases, installing vinyl trim means no painting and little maintenance, but occasionally, vinyl fades or a homeowner wants to change the color. In that case, vinyl trim can be painted using latex paint. Unlike other paints, latex will expand and contract with the vinyl, preventing cracks and peeling.

How do you cope shoe molding?

Hold Shoe Against Shoe

Lay the two pieces flat on a table with the small profiles facing each other. Make sure that the piece of shoe that won't be cut is sticking out about an inch or so further than the piece to be coped. Then pinch the pieces together, hold them steady and saw away!

How do you cut shoe molding?
  • Place a strip of shoe mold on one side of the corner. On the other side place one with a 45 degree cut. The second strip should be slightly curved and it would slide over the first strip. Once both meet, cut the remaining with the help of a small saw. This will ensure that no gaps are left between these two strips.
How do you install shoe molding?
  1. Choose Your Molding.
  2. Mark/Measure Your Molding.
  3. Cut Your Molding.
  4. Test the Fit.
  5. Sand and Finish.
  6. Ensure a No-Gap Fit.
  7. Cope Inside Corners.
  8. Install Outside Corners.
How much does shoe molding cost?

How do you cut shoe molding?

  • Place a strip of shoe mold on one side of the corner. On the other side place one with a 45 degree cut. The second strip should be slightly curved and it would slide over the first strip. Once both meet, cut the remaining with the help of a small saw. This will ensure that no gaps are left between these two strips.
How much to paint shoe molding?
  • Wood is the most common type of shoe molding, and you can buy inexpensive (paintable) pine shoe molding for $5 to $6 per eight-foot section. Hardwood shoe molding, including oak, ash, and walnut, which can be stained to match your trim, runs $6 to $10 per eight-foot section.
How to cut shoe molding angles?

How do you cut a quarter round molding?

  • Cut quarter round molding at 45 degrees in order to fit into 90-degree corners using a miter saw. For accurate miter cuts, clamp your work piece against the guide fence, ensure precise angular alignment of your miter saw, and make a slow, controlled cut through the work piece.
How to cut shoe molding corners?

What is the best saw for cutting molding?

  • Miter Saw—A much better saw to use for cutting trim molding. Also called a 'chop saw,' this tool has a fine toothed blade that you pull down on the work piece. You can cut in different angles. Radial Arm Saw —A variation of the chop saw, this one is ideal for precise cuts.
How to dead end shoe molding?

Do you miter the ends of shoe moulding?

  • Do you miter the ends on shoe moulding? We recently completed a house and did the shoe molding the same way we’ve done it for the past twelve years or so by cutting it off at a 90 degree then split the width in half and cut it again at a 22.5 degree. It would end this way at the casing or any other termination.
How to install pvc shoe molding?

What should I do Before I install shoe moulding?

  • The first thing you need to do for how to install shoe moulding is make sure the moulding is clean. Also clean around the area where you will be installing it as well. It is a good idea to have the molding already primed and painted, so if that’s what you want you should do so ahead of time.
How to make shoe sole molding?
  • Shoe Sole Molding 1 Shoe Making Basics. A shoe is made on a last, leather (in this case) is pulled tight over the last and glued onto insole board (which is stapled ... 2 Materials. I used the Shoemaster shoe design package and a Zund CNC cutting table… 3 Planning and Design… 4 Building the Mold… 5 Casting…
How to repair damaged shoe molding?
  • Fill in the nail holes with a little putty and some touch-up paint if you decided to use paint instead of stain. And you have now completed installation of the shoe molding. You can keep any extra shoe molding around to replaced damaged pieces. Just remember to paint or stain it first at the same time that you did the rest so it will match.